Home » ARC Equipments

ARC Equipments

Compact MIG/MAG for Automobile / Sheet Metal Industry Power Compact 255
Allows high speed welding without compromising quality on thin sheets with the wire feeder compactly built-in within the power source.
  • Fully portable, light weight and compact
  • Natural air cooled machine ensures maximum safety of transformer as opposed to fan-cooled where fan-failure can cause burning of coils
  • Higher metal recovery ensures lower consumption of electrodes
  • Current available in single range. Current indicator and current control handle both on front panel
  • Superior dynamic characteristics gives soft and smooth arc, minimum spatter
  • Robust and compact construction ability to withstand rough handling at sites
  • Horizontal shunt core travel ensures precise setting even after prolonged use
  • Ultra light weight for easy manoeuvrability
  • Class 'H' insulation provides longer coil life
  • Linear current indicator scale enables easy current setting
  • Low no-load loss

Specially engineered torch and components for outstanding welding performance and longer operational life
MIG Torches
  • PSF range of proven torches
  • Available in 3 or 4.5m lengths
  • Ergonomically designed
  • Light weight, durable and long life

Technical Data Power Compact 255
Power Source
Mains supply, Ph x V, Hz 3 x 415, 50
Open circuit voltage, V DC 30 - 250
Welding current range, A 30 - 250
Max. Continuous Welding Current
At 35% duty cycle, A 250
At 60% duty cycle, A 190
At 100% duty cycle, A 140
Voltage control steps (single knob) 10
No. of inductance outlets 2
Spot welding time, sec 0.2 - 2
Interval time, sec 0.2 - 2
Type of cooling Forced Air
Dimensions, l x w x h, mm 840 x 375 x 736
Weight, Kg 90
Wire Feeder
Drive system DC motor
Speed control Stepless
Feed mechanism Double roll quick changeover type
Wire feed speed, m/min 1.5 - 22
Wire diameter, mm 0.8 – 1.2
Wire type MS
Ordering Information
Power Compact 255 Package 4650686700
MIG Torch, PSF 250 3m 4650692900
MIG Torch, PSF 250 4.5m 4650692901
Regulator Dura CO2 4650193002
Regulator ICO 32B 4330193100
CO2 Heater 220V A651689045

Buddy™ Arc 400i / 400i XC
Compact and Powerful Inverter MMA Welder Robust and Powerful
The Buddy™ Arc 400i and 400i XC are heavy duty, fan cooled, IGBT based inverter controlled power sources meant for MMA / TIG (scratch-start) welding.

MMA Welding
A wide current range and powerful welding performance make the Buddy™ Arc machines suitable for a wide range of applications and electrode types such as: - General purpose
  • Low-hydrogen
  • Stainless steel
  • Cellulosic

The Buddy™ Arc 400i XC model has controlled welding dynamics that provides excellent weld properties for welding pipe root passes.

TIG Welding
The Buddy™ Arc machines are capable of performing TIG welding with precise current control. All you need is an optional TIG-torch with a gas valve, a gas regulator and a cylinder of gas. You can weld mild steel or stainless steel material with or without filler material.

Voltage Reduction Device – VRD
In some areas a voltage reduction device, or VRD, is required. VRD is a safety function that limits the open circuit voltage from the machine to less than 35V. The Buddy™ Arc are prepared for VRD and the function can easily be activated inside the power source.

Easy Settings
The simple control panel of the Buddy™ Arc makes it easy to optimise settings, reducing the time taken for achieving the best weld characteristics. These units are equipped with hot start and arc force with the possibility to adjust parameters during welding. Hot start helps to avoid starting problems while arc force sets the intensity of the arc for improved weld quality. As an option the Buddy™ Arc can be equipped with a remote control unit.

Energy Efficient
The Buddy™ Arc machines are constructed to maintain a high power factor and efficiency, thus keeping the energy cost to a minimum without affecting the weld quality.

Safety and Reliability
The Buddy™ Arc machines conform to the International Standards that ensure the reliability and safe use of these machines. These units are equipped with overheating and mains over/under voltage protection that will temporarily switch off the machines automatically to prevent any potential damage that the components might sustain.
APPLICATIONS
  • General fabrication
  • Railways
  • Shipbuilding
  • Civil construction
  • Pipe workshops
  • Inverter controlled - more efficient power usage
  • Light weight - improved mobility
  • Easy-to-use control panel - quick setup
  • Adjustable hot start - easy to strike the electrode, helps you to avoid starting problems.
  • Adjustable arc force - sets the intensity of the arc for improved weld quality.
  • Wide mains voltage tolerance - stable welding controls

Technical Data Buddy™ Arc 400i
Buddy™ Arc 400i XC
Mains voltage, V/Ph Hz 400V ± 15%, 3ph, 50Hz
Effective input current, A 21.4A
Fuse (slow), A 32
Mains cable, Ø mm² 4C x 4
Permitted load at (MMA)
60% duty cycle, A/V
100% duty cycle, A/V
400 / 36
310 / 32.4
Permitted load at (TIG) s
60% duty cycle, A/V
100% duty cycle, A/V
400 / 26
310 / 22.4
Power factor at maximum current 0.93
Efficiency at maximum current, % 85
Setting range (TIG/MMA), A 20 - 400
Open circuit voltage (OCV), V 68 (400i)
  78 (400i XC)
Reduced OCV (VRD), V <35
Dimensions lxwxh, mm 540 x 280 x 510
Weight, kg 29 (400i)
31 (400i XC)
Operating temperature -10 till 40°C
Application class S
Standards IEC 60974-1
IEC 60974-10
Ordering information
Buddy™ Arc 400i 46F0226400
Buddy™ Arc 400i XC 46F0227400
Remote Control 5m 46F1004001
Remote Control 10m 46F1005001
Delivery Content: 3m mains cable, 2 nos. male quick connectors
for Buddy Arc 400i / 400i XC.S
Optional Accessories
TXH 200V – 4m TIG Torch (for Scratch TIG) 1620607292
TXH 200V – 8m TIG Torch (for Scratch TIG) 1620607293
Welding Cable Cu 50 sq mm (100m Roll 4600600162
Welding Cable Cu 70 sq mm (100m Roll) 4600600163
Holder Handicool HC 600 2002001001
Holder Confort 600 2002001002
Heavy Duty Earth Clamp 600 2002002001
Hand Shield Armour (83 x 108mm) 2001001004
Eco Arc Helmet (83 x 108mm) 2001001003
Welding Hand Gloves 2001005001

Universal Service and Support
Our commitment and ability to deliver the expected service and support starts immediately after the order is confirmed. We endeavour to offer our customers an After Sales service, which is second to none. A strong and skilful service organisation is prepared to offer service and maintenance, calibration, validation and upgrading of equipment and software. The service organisation will offer standardised solutions for the reconditioning or modification of existing products